Filtered by vendor Cisco
Subscriptions
Filtered by product Ios
Subscriptions
Total
626 CVE
| CVE | Vendors | Products | Updated | CVSS v3.1 |
|---|---|---|---|---|
| CVE-2017-12319 | 1 Cisco | 198 1000 Integrated Services Router, 1100-4g\/6g Integrated Services Router, 1100-4g Integrated Services Router and 195 more | 2026-01-13 | 5.9 Medium |
| A vulnerability in the Border Gateway Protocol (BGP) over an Ethernet Virtual Private Network (EVPN) for Cisco IOS XE Software could allow an unauthenticated, remote attacker to cause the device to reload, resulting in a denial of service (DoS) condition, or potentially corrupt the BGP routing table, which could result in network instability. The vulnerability exists due to changes in the implementation of the BGP MPLS-Based Ethernet VPN RFC (RFC 7432) draft between IOS XE software releases. When the BGP Inclusive Multicast Ethernet Tag Route or BGP EVPN MAC/IP Advertisement Route update packet is received, it could be possible that the IP address length field is miscalculated. An attacker could exploit this vulnerability by sending a crafted BGP packet to an affected device after the BGP session was established. An exploit could allow the attacker to cause the affected device to reload or corrupt the BGP routing table; either outcome would result in a DoS. The vulnerability may be triggered when the router receives a crafted BGP message from a peer on an existing BGP session. This vulnerability affects all releases of Cisco IOS XE Software prior to software release 16.3 that support BGP EVPN configurations. If the device is not configured for EVPN, it is not vulnerable. Cisco Bug IDs: CSCui67191, CSCvg52875. | ||||
| CVE-2018-0154 | 1 Cisco | 236 1000 Integrated Services Router, 1100-4g\/6g Integrated Services Router, 1100-4g Integrated Services Router and 233 more | 2026-01-13 | 7.5 High |
| A vulnerability in the crypto engine of the Cisco Integrated Services Module for VPN (ISM-VPN) running Cisco IOS Software could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition on an affected device. The vulnerability is due to insufficient handling of VPN traffic by the affected device. An attacker could exploit this vulnerability by sending crafted VPN traffic to an affected device. A successful exploit could allow the attacker to cause the affected device to hang or crash, resulting in a DoS condition. Cisco Bug IDs: CSCvd39267. | ||||
| CVE-2017-12240 | 1 Cisco | 265 1000 Integrated Services Router, 1100-4g Integrated Services Router, 1100-4gltegb Integrated Services Router and 262 more | 2026-01-12 | 9.8 Critical |
| The DHCP relay subsystem of Cisco IOS 12.2 through 15.6 and Cisco IOS XE Software contains a vulnerability that could allow an unauthenticated, remote attacker to execute arbitrary code and gain full control of an affected system. The attacker could also cause an affected system to reload, resulting in a denial of service (DoS) condition. The vulnerability is due to a buffer overflow condition in the DHCP relay subsystem of the affected software. An attacker could exploit this vulnerability by sending a crafted DHCP Version 4 (DHCPv4) packet to an affected system. A successful exploit could allow the attacker to execute arbitrary code and gain full control of the affected system or cause the affected system to reload, resulting in a DoS condition. Cisco Bug IDs: CSCsm45390, CSCuw77959. | ||||
| CVE-2016-6415 | 1 Cisco | 3 Ios, Ios Xe, Ios Xr | 2026-01-12 | 7.5 High |
| The server IKEv1 implementation in Cisco IOS 12.2 through 12.4 and 15.0 through 15.6, IOS XE through 3.18S, IOS XR 4.3.x and 5.0.x through 5.2.x, and PIX before 7.0 allows remote attackers to obtain sensitive information from device memory via a Security Association (SA) negotiation request, aka Bug IDs CSCvb29204 and CSCvb36055 or BENIGNCERTAIN. | ||||
| CVE-2017-6742 | 1 Cisco | 2 Ios, Ios Xe | 2026-01-12 | 8.8 High |
| A vulnerability in the SNMP implementation of could allow an authenticated, remote attacker to cause a reload of the affected system or to remotely execute code. An attacker could exploit this vulnerability by sending a crafted SNMP packet to the affected device. The vulnerability is due to a buffer overflow in the affected code area. The vulnerability affects all versions of SNMP (versions 1, 2c, and 3). The attacker must know the SNMP read only community string (SNMP version 2c or earlier) or the user credentials (SNMPv3). An exploit could allow the attacker to execute arbitrary code and obtain full control of the system or to cause a reload of the affected system. Only traffic directed to the affected system can be used to exploit this vulnerability. | ||||
| CVE-2023-20186 | 1 Cisco | 2 Ios, Ios Xe | 2025-12-16 | 8 High |
| A vulnerability in the Authentication, Authorization, and Accounting (AAA) feature of Cisco IOS Software and Cisco IOS XE Software could allow an authenticated, remote attacker to bypass command authorization and copy files to or from the file system of an affected device using the Secure Copy Protocol (SCP). This vulnerability is due to incorrect processing of SCP commands in AAA command authorization checks. An attacker with valid credentials and level 15 privileges could exploit this vulnerability by using SCP to connect to an affected device from an external machine. A successful exploit could allow the attacker to obtain or change the configuration of the affected device and put files on or retrieve files from the affected device. | ||||
| CVE-2018-0197 | 1 Cisco | 2 Ios, Ios Xe | 2025-10-30 | 6.5 Medium |
| A vulnerability in the VLAN Trunking Protocol (VTP) subsystem of Cisco IOS Software and Cisco IOS XE Software could allow an unauthenticated, adjacent attacker to corrupt the internal VTP database on an affected device and cause a denial of service (DoS) condition. The vulnerability is due to a logic error in how the affected software handles a subset of VTP packets. An attacker could exploit this vulnerability by sending VTP packets in a sequence that triggers a timeout in the VTP message processing code of the affected software. A successful exploit could allow the attacker to impact the ability to create, modify, or delete VLANs and cause a DoS condition. There are workarounds that address this vulnerability. This vulnerability affects Cisco devices that are running a vulnerable release of Cisco IOS Software or Cisco IOS XE Software, are operating in VTP client mode or VTP server mode, and do not have a VTP domain name configured. The default configuration for Cisco devices that are running Cisco IOS Software or Cisco IOS XE Software and support VTP is to operate in VTP server mode with no domain name configured. | ||||
| CVE-2021-34705 | 1 Cisco | 2 Ios, Ios Xe | 2025-10-30 | 5.3 Medium |
| A vulnerability in the Voice Telephony Service Provider (VTSP) service of Cisco IOS Software and Cisco IOS XE Software could allow an unauthenticated, remote attacker to bypass configured destination patterns and dial arbitrary numbers. This vulnerability is due to insufficient validation of dial strings at Foreign Exchange Office (FXO) interfaces. An attacker could exploit this vulnerability by sending a malformed dial string to an affected device via either the ISDN protocol or SIP. A successful exploit could allow the attacker to conduct toll fraud, resulting in unexpected financial impact to affected customers. | ||||
| CVE-2025-20169 | 1 Cisco | 2 Ios, Ios Xe | 2025-10-30 | 7.7 High |
| A vulnerability in the SNMP subsystem of Cisco IOS Software and Cisco IOS XE Software could allow an authenticated, remote attacker to cause a DoS condition on an affected device. This vulnerability is due to improper error handling when parsing SNMP requests. An attacker could exploit this vulnerability by sending a crafted SNMP request to an affected device. A successful exploit could allow the attacker to cause the device to reload unexpectedly, resulting in a DoS condition. This vulnerability affects SNMP versions 1, 2c, and 3. To exploit this vulnerability through SNMP v2c or earlier, the attacker must know a valid read-write or read-only SNMP community string for the affected system. To exploit this vulnerability through SNMP v3, the attacker must have valid SNMP user credentials for the affected system. | ||||
| CVE-2023-20109 | 1 Cisco | 2 Ios, Ios Xe | 2025-10-28 | 6.6 Medium |
| A vulnerability in the Cisco Group Encrypted Transport VPN (GET VPN) feature of Cisco IOS Software and Cisco IOS XE Software could allow an authenticated, remote attacker who has administrative control of either a group member or a key server to execute arbitrary code on an affected device or cause the device to crash. This vulnerability is due to insufficient validation of attributes in the Group Domain of Interpretation (GDOI) and G-IKEv2 protocols of the GET VPN feature. An attacker could exploit this vulnerability by either compromising an installed key server or modifying the configuration of a group member to point to a key server that is controlled by the attacker. A successful exploit could allow the attacker to execute arbitrary code and gain full control of the affected system or cause the affected system to reload, resulting in a denial of service (DoS) condition. For more information, see the Details ["#details"] section of this advisory. | ||||
| CVE-2004-1464 | 1 Cisco | 1 Ios | 2025-10-22 | 5.9 Medium |
| Cisco IOS 12.2(15) and earlier allows remote attackers to cause a denial of service (refused VTY (virtual terminal) connections), via a crafted TCP connection to the Telnet or reverse Telnet port. | ||||
| CVE-2017-6744 | 1 Cisco | 1 Ios | 2025-10-22 | 8.8 High |
| The Simple Network Management Protocol (SNMP) subsystem of Cisco IOS and IOS XE Software contains multiple vulnerabilities that could allow an authenticated, remote attacker to remotely execute code on an affected system or cause an affected system to reload. An attacker could exploit these vulnerabilities by sending a crafted SNMP packet to an affected system via IPv4 or IPv6. Only traffic directed to an affected system can be used to exploit these vulnerabilities. The vulnerabilities are due to a buffer overflow condition in the SNMP subsystem of the affected software. The vulnerabilities affect all versions of SNMP - Versions 1, 2c, and 3. To exploit these vulnerabilities via SNMP Version 2c or earlier, the attacker must know the SNMP read-only community string for the affected system. To exploit these vulnerabilities via SNMP Version 3, the attacker must have user credentials for the affected system. A successful exploit could allow the attacker to execute arbitrary code and obtain full control of the affected system or cause the affected system to reload. Customers are advised to apply the workaround as contained in the Workarounds section below. Fixed software information is available via the Cisco IOS Software Checker. All devices that have enabled SNMP and have not explicitly excluded the affected MIBs or OIDs should be considered vulnerable. There are workarounds that address these vulnerabilities. | ||||
| CVE-2017-6743 | 1 Cisco | 2 Ios, Ios Xe | 2025-10-22 | 8.8 High |
| The Simple Network Management Protocol (SNMP) subsystem of Cisco IOS and IOS XE Software contains multiple vulnerabilities that could allow an authenticated, remote attacker to remotely execute code on an affected system or cause an affected system to reload. An attacker could exploit these vulnerabilities by sending a crafted SNMP packet to an affected system via IPv4 or IPv6. Only traffic directed to an affected system can be used to exploit these vulnerabilities. The vulnerabilities are due to a buffer overflow condition in the SNMP subsystem of the affected software. The vulnerabilities affect all versions of SNMP - Versions 1, 2c, and 3. To exploit these vulnerabilities via SNMP Version 2c or earlier, the attacker must know the SNMP read-only community string for the affected system. To exploit these vulnerabilities via SNMP Version 3, the attacker must have user credentials for the affected system. A successful exploit could allow the attacker to execute arbitrary code and obtain full control of the affected system or cause the affected system to reload. Customers are advised to apply the workaround as contained in the Workarounds section below. Fixed software information is available via the Cisco IOS Software Checker. All devices that have enabled SNMP and have not explicitly excluded the affected MIBs or OIDs should be considered vulnerable. There are workarounds that address these vulnerabilities. | ||||
| CVE-2017-6740 | 1 Cisco | 2 Ios, Ios Xe | 2025-10-22 | 8.8 High |
| The Simple Network Management Protocol (SNMP) subsystem of Cisco IOS and IOS XE Software contains multiple vulnerabilities that could allow an authenticated, remote attacker to remotely execute code on an affected system or cause an affected system to reload. An attacker could exploit these vulnerabilities by sending a crafted SNMP packet to an affected system via IPv4 or IPv6. Only traffic directed to an affected system can be used to exploit these vulnerabilities. The vulnerabilities are due to a buffer overflow condition in the SNMP subsystem of the affected software. The vulnerabilities affect all versions of SNMP - Versions 1, 2c, and 3. To exploit these vulnerabilities via SNMP Version 2c or earlier, the attacker must know the SNMP read-only community string for the affected system. To exploit these vulnerabilities via SNMP Version 3, the attacker must have user credentials for the affected system. A successful exploit could allow the attacker to execute arbitrary code and obtain full control of the affected system or cause the affected system to reload. Customers are advised to apply the workaround as contained in the Workarounds section below. Fixed software information is available via the Cisco IOS Software Checker. All devices that have enabled SNMP and have not explicitly excluded the affected MIBs or OIDs should be considered vulnerable. There are workarounds that address these vulnerabilities. | ||||
| CVE-2017-6739 | 1 Cisco | 2 Ios, Ios Xe | 2025-10-22 | 8.8 High |
| A vulnerability in the SNMP implementation of could allow an authenticated, remote attacker to cause a reload of the affected system or to remotely execute code. An attacker could exploit this vulnerability by sending a crafted SNMP packet to the affected device. The vulnerability is due to a buffer overflow in the affected code area. The vulnerability affects all versions of SNMP (versions 1, 2c, and 3). The attacker must know the SNMP read only community string (SNMP version 2c or earlier) or the user credentials (SNMPv3). An exploit could allow the attacker to execute arbitrary code and obtain full control of the system or to cause a reload of the affected system. Only traffic directed to the affected system can be used to exploit this vulnerability. | ||||
| CVE-2017-6738 | 1 Cisco | 2 Ios, Ios Xe | 2025-10-22 | 8.8 High |
| The Simple Network Management Protocol (SNMP) subsystem of Cisco IOS and IOS XE Software contains multiple vulnerabilities that could allow an authenticated, remote attacker to remotely execute code on an affected system or cause an affected system to reload. An attacker could exploit these vulnerabilities by sending a crafted SNMP packet to an affected system via IPv4 or IPv6. Only traffic directed to an affected system can be used to exploit these vulnerabilities. The vulnerabilities are due to a buffer overflow condition in the SNMP subsystem of the affected software. The vulnerabilities affect all versions of SNMP - Versions 1, 2c, and 3. To exploit these vulnerabilities via SNMP Version 2c or earlier, the attacker must know the SNMP read-only community string for the affected system. To exploit these vulnerabilities via SNMP Version 3, the attacker must have user credentials for the affected system. A successful exploit could allow the attacker to execute arbitrary code and obtain full control of the affected system or cause the affected system to reload. Customers are advised to apply the workaround as contained in the Workarounds section below. Fixed software information is available via the Cisco IOS Software Checker. All devices that have enabled SNMP and have not explicitly excluded the affected MIBs or OIDs should be considered vulnerable. There are workarounds that address these vulnerabilities. | ||||
| CVE-2017-6737 | 1 Cisco | 2 Ios, Ios Xe | 2025-10-22 | 8.8 High |
| A vulnerability in the SNMP implementation of could allow an authenticated, remote attacker to cause a reload of the affected system or to remotely execute code. An attacker could exploit this vulnerability by sending a crafted SNMP packet to the affected device. The vulnerability is due to a buffer overflow in the affected code area. The vulnerability affects all versions of SNMP (versions 1, 2c, and 3). The attacker must know the SNMP read only community string (SNMP version 2c or earlier) or the user credentials (SNMPv3). An exploit could allow the attacker to execute arbitrary code and obtain full control of the system or to cause a reload of the affected system. Only traffic directed to the affected system can be used to exploit this vulnerability. | ||||
| CVE-2017-6736 | 1 Cisco | 2 Ios, Ios Xe | 2025-10-22 | 8.8 High |
| The Simple Network Management Protocol (SNMP) subsystem of Cisco IOS and IOS XE Software contains multiple vulnerabilities that could allow an authenticated, remote attacker to remotely execute code on an affected system or cause an affected system to reload. An attacker could exploit these vulnerabilities by sending a crafted SNMP packet to an affected system via IPv4 or IPv6. Only traffic directed to an affected system can be used to exploit these vulnerabilities. The vulnerabilities are due to a buffer overflow condition in the SNMP subsystem of the affected software. The vulnerabilities affect all versions of SNMP - Versions 1, 2c, and 3. To exploit these vulnerabilities via SNMP Version 2c or earlier, the attacker must know the SNMP read-only community string for the affected system. To exploit these vulnerabilities via SNMP Version 3, the attacker must have user credentials for the affected system. A successful exploit could allow the attacker to execute arbitrary code and obtain full control of the affected system or cause the affected system to reload. Customers are advised to apply the workaround as contained in the Workarounds section below. Fixed software information is available via the Cisco IOS Software Checker. All devices that have enabled SNMP and have not explicitly excluded the affected MIBs or OIDs should be considered vulnerable. There are workarounds that address these vulnerabilities. | ||||
| CVE-2017-6663 | 1 Cisco | 2 Ios, Ios Xe | 2025-10-22 | 6.5 Medium |
| A vulnerability in the Autonomic Networking feature of Cisco IOS Software and Cisco IOS XE Software could allow an unauthenticated, adjacent attacker to cause autonomic nodes of an affected system to reload, resulting in a denial of service (DoS) condition. More Information: CSCvd88936. Known Affected Releases: Denali-16.2.1 Denali-16.3.1. | ||||
| CVE-2017-6627 | 1 Cisco | 2 Ios, Ios Xe | 2025-10-22 | 7.5 High |
| A vulnerability in the UDP processing code of Cisco IOS 15.1, 15.2, and 15.4 and IOS XE 3.14 through 3.18 could allow an unauthenticated, remote attacker to cause the input queue of an affected system to hold UDP packets, causing an interface queue wedge and a denial of service (DoS) condition. The vulnerability is due to Cisco IOS Software application changes that create UDP sockets and leave the sockets idle without closing them. An attacker could exploit this vulnerability by sending UDP packets with a destination port of 0 to an affected device. A successful exploit could allow the attacker to cause UDP packets to be held in the input interfaces queue, resulting in a DoS condition. The input interface queue will stop holding UDP packets when it receives 250 packets. Cisco Bug IDs: CSCup10024, CSCva55744, CSCva95506. | ||||