Filtered by vendor Linux
Subscriptions
Total
16828 CVE
| CVE | Vendors | Products | Updated | CVSS v3.1 |
|---|---|---|---|---|
| CVE-2026-23009 | 1 Linux | 1 Linux Kernel | 2026-01-26 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: xhci: sideband: don't dereference freed ring when removing sideband endpoint xhci_sideband_remove_endpoint() incorrecly assumes that the endpoint is running and has a valid transfer ring. Lianqin reported a crash during suspend/wake-up stress testing, and found the cause to be dereferencing a non-existing transfer ring 'ep->ring' during xhci_sideband_remove_endpoint(). The endpoint and its ring may be in unknown state if this function is called after xHCI was reinitialized in resume (lost power), or if device is being re-enumerated, disconnected or endpoint already dropped. Fix this by both removing unnecessary ring access, and by checking ep->ring exists before dereferencing it. Also make sure endpoint is running before attempting to stop it. Remove the xhci_initialize_ring_info() call during sideband endpoint removal as is it only initializes ring structure enqueue, dequeue and cycle state values to their starting values without changing actual hardware enqueue, dequeue and cycle state. Leaving them out of sync is worse than leaving it as it is. The endpoint will get freed in after this in most usecases. If the (audio) class driver want's to reuse the endpoint after offload then it is up to the class driver to ensure endpoint is properly set up. | ||||
| CVE-2026-23007 | 1 Linux | 1 Linux Kernel | 2026-01-26 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: block: zero non-PI portion of auto integrity buffer The auto-generated integrity buffer for writes needs to be fully initialized before being passed to the underlying block device, otherwise the uninitialized memory can be read back by userspace or anyone with physical access to the storage device. If protection information is generated, that portion of the integrity buffer is already initialized. The integrity data is also zeroed if PI generation is disabled via sysfs or the PI tuple size is 0. However, this misses the case where PI is generated and the PI tuple size is nonzero, but the metadata size is larger than the PI tuple. In this case, the remainder ("opaque") of the metadata is left uninitialized. Generalize the BLK_INTEGRITY_CSUM_NONE check to cover any case when the metadata is larger than just the PI tuple. | ||||
| CVE-2026-23012 | 1 Linux | 1 Linux Kernel | 2026-01-26 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: mm/damon/core: remove call_control in inactive contexts If damon_call() is executed against a DAMON context that is not running, the function returns error while keeping the damon_call_control object linked to the context's call_controls list. Let's suppose the object is deallocated after the damon_call(), and yet another damon_call() is executed against the same context. The function tries to add the new damon_call_control object to the call_controls list, which still has the pointer to the previous damon_call_control object, which is deallocated. As a result, use-after-free happens. This can actually be triggered using the DAMON sysfs interface. It is not easily exploitable since it requires the sysfs write permission and making a definitely weird file writes, though. Please refer to the report for more details about the issue reproduction steps. Fix the issue by making two changes. Firstly, move the final kdamond_call() for cancelling all existing damon_call() requests from terminating DAMON context to be done before the ctx->kdamond reset. This makes any code that sees NULL ctx->kdamond can safely assume the context may not access damon_call() requests anymore. Secondly, let damon_call() to cleanup the damon_call_control objects that were added to the already-terminated DAMON context, before returning the error. | ||||
| CVE-2026-23002 | 1 Linux | 1 Linux Kernel | 2026-01-26 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: lib/buildid: use __kernel_read() for sleepable context Prevent a "BUG: unable to handle kernel NULL pointer dereference in filemap_read_folio". For the sleepable context, convert freader to use __kernel_read() instead of direct page cache access via read_cache_folio(). This simplifies the faultable code path by using the standard kernel file reading interface which handles all the complexity of reading file data. At the moment we are not changing the code for non-sleepable context which uses filemap_get_folio() and only succeeds if the target folios are already in memory and up-to-date. The reason is to keep the patch simple and easier to backport to stable kernels. Syzbot repro does not crash the kernel anymore and the selftests run successfully. In the follow up we will make __kernel_read() with IOCB_NOWAIT work for non-sleepable contexts. In addition, I would like to replace the secretmem check with a more generic approach and will add fstest for the buildid code. | ||||
| CVE-2026-22993 | 1 Linux | 1 Linux Kernel | 2026-01-26 | 7.0 High |
| In the Linux kernel, the following vulnerability has been resolved: idpf: Fix RSS LUT NULL ptr issue after soft reset During soft reset, the RSS LUT is freed and not restored unless the interface is up. If an ethtool command that accesses the rss lut is attempted immediately after reset, it will result in NULL ptr dereference. Also, there is no need to reset the rss lut if the soft reset does not involve queue count change. After soft reset, set the RSS LUT to default values based on the updated queue count only if the reset was a result of a queue count change and the LUT was not configured by the user. In all other cases, don't touch the LUT. Steps to reproduce: ** Bring the interface down (if up) ifconfig eth1 down ** update the queue count (eg., 27->20) ethtool -L eth1 combined 20 ** display the RSS LUT ethtool -x eth1 [82375.558338] BUG: kernel NULL pointer dereference, address: 0000000000000000 [82375.558373] #PF: supervisor read access in kernel mode [82375.558391] #PF: error_code(0x0000) - not-present page [82375.558408] PGD 0 P4D 0 [82375.558421] Oops: Oops: 0000 [#1] SMP NOPTI <snip> [82375.558516] RIP: 0010:idpf_get_rxfh+0x108/0x150 [idpf] [82375.558786] Call Trace: [82375.558793] <TASK> [82375.558804] rss_prepare.isra.0+0x187/0x2a0 [82375.558827] rss_prepare_data+0x3a/0x50 [82375.558845] ethnl_default_doit+0x13d/0x3e0 [82375.558863] genl_family_rcv_msg_doit+0x11f/0x180 [82375.558886] genl_rcv_msg+0x1ad/0x2b0 [82375.558902] ? __pfx_ethnl_default_doit+0x10/0x10 [82375.558920] ? __pfx_genl_rcv_msg+0x10/0x10 [82375.558937] netlink_rcv_skb+0x58/0x100 [82375.558957] genl_rcv+0x2c/0x50 [82375.558971] netlink_unicast+0x289/0x3e0 [82375.558988] netlink_sendmsg+0x215/0x440 [82375.559005] __sys_sendto+0x234/0x240 [82375.559555] __x64_sys_sendto+0x28/0x30 [82375.560068] x64_sys_call+0x1909/0x1da0 [82375.560576] do_syscall_64+0x7a/0xfa0 [82375.561076] ? clear_bhb_loop+0x60/0xb0 [82375.561567] entry_SYSCALL_64_after_hwframe+0x76/0x7e <snip> | ||||
| CVE-2026-22987 | 1 Linux | 1 Linux Kernel | 2026-01-26 | 7.0 High |
| In the Linux kernel, the following vulnerability has been resolved: net/sched: act_api: avoid dereferencing ERR_PTR in tcf_idrinfo_destroy syzbot reported a crash in tc_act_in_hw() during netns teardown where tcf_idrinfo_destroy() passed an ERR_PTR(-EBUSY) value as a tc_action pointer, leading to an invalid dereference. Guard against ERR_PTR entries when iterating the action IDR so teardown does not call tc_act_in_hw() on an error pointer. | ||||
| CVE-2026-22988 | 1 Linux | 1 Linux Kernel | 2026-01-26 | 7.0 High |
| In the Linux kernel, the following vulnerability has been resolved: arp: do not assume dev_hard_header() does not change skb->head arp_create() is the only dev_hard_header() caller making assumption about skb->head being unchanged. A recent commit broke this assumption. Initialize @arp pointer after dev_hard_header() call. | ||||
| CVE-2026-23000 | 1 Linux | 1 Linux Kernel | 2026-01-26 | 7.0 High |
| In the Linux kernel, the following vulnerability has been resolved: net/mlx5e: Fix crash on profile change rollback failure mlx5e_netdev_change_profile can fail to attach a new profile and can fail to rollback to old profile, in such case, we could end up with a dangling netdev with a fully reset netdev_priv. A retry to change profile, e.g. another attempt to call mlx5e_netdev_change_profile via switchdev mode change, will crash trying to access the now NULL priv->mdev. This fix allows mlx5e_netdev_change_profile() to handle previous failures and an empty priv, by not assuming priv is valid. Pass netdev and mdev to all flows requiring mlx5e_netdev_change_profile() and avoid passing priv. In mlx5e_netdev_change_profile() check if current priv is valid, and if not, just attach the new profile without trying to access the old one. This fixes the following oops, when enabling switchdev mode for the 2nd time after first time failure: ## Enabling switchdev mode first time: mlx5_core 0012:03:00.1: E-Switch: Supported tc chains and prios offload workqueue: Failed to create a rescuer kthread for wq "mlx5e": -EINTR mlx5_core 0012:03:00.1: mlx5e_netdev_init_profile:6214:(pid 37199): mlx5e_priv_init failed, err=-12 mlx5_core 0012:03:00.1 gpu3rdma1: mlx5e_netdev_change_profile: new profile init failed, -12 workqueue: Failed to create a rescuer kthread for wq "mlx5e": -EINTR mlx5_core 0012:03:00.1: mlx5e_netdev_init_profile:6214:(pid 37199): mlx5e_priv_init failed, err=-12 mlx5_core 0012:03:00.1 gpu3rdma1: mlx5e_netdev_change_profile: failed to rollback to orig profile, -12 ^^^^^^^^ mlx5_core 0000:00:03.0: E-Switch: Disable: mode(LEGACY), nvfs(0), necvfs(0), active vports(0) ## retry: Enabling switchdev mode 2nd time: mlx5_core 0000:00:03.0: E-Switch: Supported tc chains and prios offload BUG: kernel NULL pointer dereference, address: 0000000000000038 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 0 P4D 0 Oops: Oops: 0000 [#1] SMP NOPTI CPU: 13 UID: 0 PID: 520 Comm: devlink Not tainted 6.18.0-rc4+ #91 PREEMPT(voluntary) Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-2.fc40 04/01/2014 RIP: 0010:mlx5e_detach_netdev+0x3c/0x90 Code: 50 00 00 f0 80 4f 78 02 48 8b bf e8 07 00 00 48 85 ff 74 16 48 8b 73 78 48 d1 ee 83 e6 01 83 f6 01 40 0f b6 f6 e8 c4 42 00 00 <48> 8b 45 38 48 85 c0 74 08 48 89 df e8 cc 47 40 1e 48 8b bb f0 07 RSP: 0018:ffffc90000673890 EFLAGS: 00010246 RAX: 0000000000000000 RBX: ffff8881036a89c0 RCX: 0000000000000000 RDX: ffff888113f63800 RSI: ffffffff822fe720 RDI: 0000000000000000 RBP: 0000000000000000 R08: 0000000000002dcd R09: 0000000000000000 R10: ffffc900006738e8 R11: 00000000ffffffff R12: 0000000000000000 R13: 0000000000000000 R14: ffff8881036a89c0 R15: 0000000000000000 FS: 00007fdfb8384740(0000) GS:ffff88856a9d6000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000038 CR3: 0000000112ae0005 CR4: 0000000000370ef0 Call Trace: <TASK> mlx5e_netdev_change_profile+0x45/0xb0 mlx5e_vport_rep_load+0x27b/0x2d0 mlx5_esw_offloads_rep_load+0x72/0xf0 esw_offloads_enable+0x5d0/0x970 mlx5_eswitch_enable_locked+0x349/0x430 ? is_mp_supported+0x57/0xb0 mlx5_devlink_eswitch_mode_set+0x26b/0x430 devlink_nl_eswitch_set_doit+0x6f/0xf0 genl_family_rcv_msg_doit+0xe8/0x140 genl_rcv_msg+0x18b/0x290 ? __pfx_devlink_nl_pre_doit+0x10/0x10 ? __pfx_devlink_nl_eswitch_set_doit+0x10/0x10 ? __pfx_devlink_nl_post_doit+0x10/0x10 ? __pfx_genl_rcv_msg+0x10/0x10 netlink_rcv_skb+0x52/0x100 genl_rcv+0x28/0x40 netlink_unicast+0x282/0x3e0 ? __alloc_skb+0xd6/0x190 netlink_sendmsg+0x1f7/0x430 __sys_sendto+0x213/0x220 ? __sys_recvmsg+0x6a/0xd0 __x64_sys_sendto+0x24/0x30 do_syscall_64+0x50/0x1f0 entry_SYSCALL_64_after_hwframe+0x76/0x7e RIP: 0033:0x7fdfb8495047 | ||||
| CVE-2026-22996 | 1 Linux | 1 Linux Kernel | 2026-01-26 | 7.0 High |
| In the Linux kernel, the following vulnerability has been resolved: net/mlx5e: Don't store mlx5e_priv in mlx5e_dev devlink priv mlx5e_priv is an unstable structure that can be memset(0) if profile attaching fails, mlx5e_priv in mlx5e_dev devlink private is used to reference the netdev and mdev associated with that struct. Instead, store netdev directly into mlx5e_dev and get mdev from the containing mlx5_adev aux device structure. This fixes a kernel oops in mlx5e_remove when switchdev mode fails due to change profile failure. $ devlink dev eswitch set pci/0000:00:03.0 mode switchdev Error: mlx5_core: Failed setting eswitch to offloads. dmesg: workqueue: Failed to create a rescuer kthread for wq "mlx5e": -EINTR mlx5_core 0012:03:00.1: mlx5e_netdev_init_profile:6214:(pid 37199): mlx5e_priv_init failed, err=-12 mlx5_core 0012:03:00.1 gpu3rdma1: mlx5e_netdev_change_profile: new profile init failed, -12 workqueue: Failed to create a rescuer kthread for wq "mlx5e": -EINTR mlx5_core 0012:03:00.1: mlx5e_netdev_init_profile:6214:(pid 37199): mlx5e_priv_init failed, err=-12 mlx5_core 0012:03:00.1 gpu3rdma1: mlx5e_netdev_change_profile: failed to rollback to orig profile, -12 $ devlink dev reload pci/0000:00:03.0 ==> oops BUG: kernel NULL pointer dereference, address: 0000000000000520 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 0 P4D 0 Oops: Oops: 0000 [#1] SMP NOPTI CPU: 3 UID: 0 PID: 521 Comm: devlink Not tainted 6.18.0-rc5+ #117 PREEMPT(voluntary) Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-2.fc40 04/01/2014 RIP: 0010:mlx5e_remove+0x68/0x130 RSP: 0018:ffffc900034838f0 EFLAGS: 00010246 RAX: ffff88810283c380 RBX: ffff888101874400 RCX: ffffffff826ffc45 RDX: 0000000000000000 RSI: 0000000000000001 RDI: 0000000000000000 RBP: ffff888102d789c0 R08: ffff8881007137f0 R09: ffff888100264e10 R10: ffffc90003483898 R11: ffffc900034838a0 R12: ffff888100d261a0 R13: ffff888100d261a0 R14: ffff8881018749a0 R15: ffff888101874400 FS: 00007f8565fea740(0000) GS:ffff88856a759000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000520 CR3: 000000010b11a004 CR4: 0000000000370ef0 Call Trace: <TASK> device_release_driver_internal+0x19c/0x200 bus_remove_device+0xc6/0x130 device_del+0x160/0x3d0 ? devl_param_driverinit_value_get+0x2d/0x90 mlx5_detach_device+0x89/0xe0 mlx5_unload_one_devl_locked+0x3a/0x70 mlx5_devlink_reload_down+0xc8/0x220 devlink_reload+0x7d/0x260 devlink_nl_reload_doit+0x45b/0x5a0 genl_family_rcv_msg_doit+0xe8/0x140 | ||||
| CVE-2026-23004 | 1 Linux | 1 Linux Kernel | 2026-01-26 | 4.7 Medium |
| In the Linux kernel, the following vulnerability has been resolved: dst: fix races in rt6_uncached_list_del() and rt_del_uncached_list() syzbot was able to crash the kernel in rt6_uncached_list_flush_dev() in an interesting way [1] Crash happens in list_del_init()/INIT_LIST_HEAD() while writing list->prev, while the prior write on list->next went well. static inline void INIT_LIST_HEAD(struct list_head *list) { WRITE_ONCE(list->next, list); // This went well WRITE_ONCE(list->prev, list); // Crash, @list has been freed. } Issue here is that rt6_uncached_list_del() did not attempt to lock ul->lock, as list_empty(&rt->dst.rt_uncached) returned true because the WRITE_ONCE(list->next, list) happened on the other CPU. We might use list_del_init_careful() and list_empty_careful(), or make sure rt6_uncached_list_del() always grabs the spinlock whenever rt->dst.rt_uncached_list has been set. A similar fix is neeed for IPv4. [1] BUG: KASAN: slab-use-after-free in INIT_LIST_HEAD include/linux/list.h:46 [inline] BUG: KASAN: slab-use-after-free in list_del_init include/linux/list.h:296 [inline] BUG: KASAN: slab-use-after-free in rt6_uncached_list_flush_dev net/ipv6/route.c:191 [inline] BUG: KASAN: slab-use-after-free in rt6_disable_ip+0x633/0x730 net/ipv6/route.c:5020 Write of size 8 at addr ffff8880294cfa78 by task kworker/u8:14/3450 CPU: 0 UID: 0 PID: 3450 Comm: kworker/u8:14 Tainted: G L syzkaller #0 PREEMPT_{RT,(full)} Tainted: [L]=SOFTLOCKUP Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/25/2025 Workqueue: netns cleanup_net Call Trace: <TASK> dump_stack_lvl+0xe8/0x150 lib/dump_stack.c:120 print_address_description mm/kasan/report.c:378 [inline] print_report+0xca/0x240 mm/kasan/report.c:482 kasan_report+0x118/0x150 mm/kasan/report.c:595 INIT_LIST_HEAD include/linux/list.h:46 [inline] list_del_init include/linux/list.h:296 [inline] rt6_uncached_list_flush_dev net/ipv6/route.c:191 [inline] rt6_disable_ip+0x633/0x730 net/ipv6/route.c:5020 addrconf_ifdown+0x143/0x18a0 net/ipv6/addrconf.c:3853 addrconf_notify+0x1bc/0x1050 net/ipv6/addrconf.c:-1 notifier_call_chain+0x19d/0x3a0 kernel/notifier.c:85 call_netdevice_notifiers_extack net/core/dev.c:2268 [inline] call_netdevice_notifiers net/core/dev.c:2282 [inline] netif_close_many+0x29c/0x410 net/core/dev.c:1785 unregister_netdevice_many_notify+0xb50/0x2330 net/core/dev.c:12353 ops_exit_rtnl_list net/core/net_namespace.c:187 [inline] ops_undo_list+0x3dc/0x990 net/core/net_namespace.c:248 cleanup_net+0x4de/0x7b0 net/core/net_namespace.c:696 process_one_work kernel/workqueue.c:3257 [inline] process_scheduled_works+0xad1/0x1770 kernel/workqueue.c:3340 worker_thread+0x8a0/0xda0 kernel/workqueue.c:3421 kthread+0x711/0x8a0 kernel/kthread.c:463 ret_from_fork+0x510/0xa50 arch/x86/kernel/process.c:158 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:246 </TASK> Allocated by task 803: kasan_save_stack mm/kasan/common.c:57 [inline] kasan_save_track+0x3e/0x80 mm/kasan/common.c:78 unpoison_slab_object mm/kasan/common.c:340 [inline] __kasan_slab_alloc+0x6c/0x80 mm/kasan/common.c:366 kasan_slab_alloc include/linux/kasan.h:253 [inline] slab_post_alloc_hook mm/slub.c:4953 [inline] slab_alloc_node mm/slub.c:5263 [inline] kmem_cache_alloc_noprof+0x18d/0x6c0 mm/slub.c:5270 dst_alloc+0x105/0x170 net/core/dst.c:89 ip6_dst_alloc net/ipv6/route.c:342 [inline] icmp6_dst_alloc+0x75/0x460 net/ipv6/route.c:3333 mld_sendpack+0x683/0xe60 net/ipv6/mcast.c:1844 mld_send_cr net/ipv6/mcast.c:2154 [inline] mld_ifc_work+0x83e/0xd60 net/ipv6/mcast.c:2693 process_one_work kernel/workqueue.c:3257 [inline] process_scheduled_works+0xad1/0x1770 kernel/workqueue.c:3340 worker_thread+0x8a0/0xda0 kernel/workqueue.c:3421 kthread+0x711/0x8a0 kernel/kthread.c:463 ret_from_fork+0x510/0xa50 arch/x86/kernel/process.c:158 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entr ---truncated--- | ||||
| CVE-2026-22995 | 1 Linux | 1 Linux Kernel | 2026-01-26 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: ublk: fix use-after-free in ublk_partition_scan_work A race condition exists between the async partition scan work and device teardown that can lead to a use-after-free of ub->ub_disk: 1. ublk_ctrl_start_dev() schedules partition_scan_work after add_disk() 2. ublk_stop_dev() calls ublk_stop_dev_unlocked() which does: - del_gendisk(ub->ub_disk) - ublk_detach_disk() sets ub->ub_disk = NULL - put_disk() which may free the disk 3. The worker ublk_partition_scan_work() then dereferences ub->ub_disk leading to UAF Fix this by using ublk_get_disk()/ublk_put_disk() in the worker to hold a reference to the disk during the partition scan. The spinlock in ublk_get_disk() synchronizes with ublk_detach_disk() ensuring the worker either gets a valid reference or sees NULL and exits early. Also change flush_work() to cancel_work_sync() to avoid running the partition scan work unnecessarily when the disk is already detached. | ||||
| CVE-2026-22994 | 1 Linux | 1 Linux Kernel | 2026-01-26 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: bpf: Fix reference count leak in bpf_prog_test_run_xdp() syzbot is reporting unregister_netdevice: waiting for sit0 to become free. Usage count = 2 problem. A debug printk() patch found that a refcount is obtained at xdp_convert_md_to_buff() from bpf_prog_test_run_xdp(). According to commit ec94670fcb3b ("bpf: Support specifying ingress via xdp_md context in BPF_PROG_TEST_RUN"), the refcount obtained by xdp_convert_md_to_buff() will be released by xdp_convert_buff_to_md(). Therefore, we can consider that the error handling path introduced by commit 1c1949982524 ("bpf: introduce frags support to bpf_prog_test_run_xdp()") forgot to call xdp_convert_buff_to_md(). | ||||
| CVE-2026-22992 | 1 Linux | 1 Linux Kernel | 2026-01-26 | 7.0 High |
| In the Linux kernel, the following vulnerability has been resolved: libceph: return the handler error from mon_handle_auth_done() Currently any error from ceph_auth_handle_reply_done() is propagated via finish_auth() but isn't returned from mon_handle_auth_done(). This results in higher layers learning that (despite the monitor considering us to be successfully authenticated) something went wrong in the authentication phase and reacting accordingly, but msgr2 still trying to proceed with establishing the session in the background. In the case of secure mode this can trigger a WARN in setup_crypto() and later lead to a NULL pointer dereference inside of prepare_auth_signature(). | ||||
| CVE-2026-22991 | 1 Linux | 1 Linux Kernel | 2026-01-26 | 7.0 High |
| In the Linux kernel, the following vulnerability has been resolved: libceph: make free_choose_arg_map() resilient to partial allocation free_choose_arg_map() may dereference a NULL pointer if its caller fails after a partial allocation. For example, in decode_choose_args(), if allocation of arg_map->args fails, execution jumps to the fail label and free_choose_arg_map() is called. Since arg_map->size is updated to a non-zero value before memory allocation, free_choose_arg_map() will iterate over arg_map->args and dereference a NULL pointer. To prevent this potential NULL pointer dereference and make free_choose_arg_map() more resilient, add checks for pointers before iterating. | ||||
| CVE-2026-22990 | 1 Linux | 1 Linux Kernel | 2026-01-26 | 7.0 High |
| In the Linux kernel, the following vulnerability has been resolved: libceph: replace overzealous BUG_ON in osdmap_apply_incremental() If the osdmap is (maliciously) corrupted such that the incremental osdmap epoch is different from what is expected, there is no need to BUG. Instead, just declare the incremental osdmap to be invalid. | ||||
| CVE-2026-22989 | 1 Linux | 1 Linux Kernel | 2026-01-26 | 7.0 High |
| In the Linux kernel, the following vulnerability has been resolved: nfsd: check that server is running in unlock_filesystem If we are trying to unlock the filesystem via an administrative interface and nfsd isn't running, it crashes the server. This happens currently because nfsd4_revoke_states() access state structures (eg., conf_id_hashtbl) that has been freed as a part of the server shutdown. [ 59.465072] Call trace: [ 59.465308] nfsd4_revoke_states+0x1b4/0x898 [nfsd] (P) [ 59.465830] write_unlock_fs+0x258/0x440 [nfsd] [ 59.466278] nfsctl_transaction_write+0xb0/0x120 [nfsd] [ 59.466780] vfs_write+0x1f0/0x938 [ 59.467088] ksys_write+0xfc/0x1f8 [ 59.467395] __arm64_sys_write+0x74/0xb8 [ 59.467746] invoke_syscall.constprop.0+0xdc/0x1e8 [ 59.468177] do_el0_svc+0x154/0x1d8 [ 59.468489] el0_svc+0x40/0xe0 [ 59.468767] el0t_64_sync_handler+0xa0/0xe8 [ 59.469138] el0t_64_sync+0x1ac/0x1b0 Ensure this can't happen by taking the nfsd_mutex and checking that the server is still up, and then holding the mutex across the call to nfsd4_revoke_states(). | ||||
| CVE-2026-22986 | 1 Linux | 1 Linux Kernel | 2026-01-26 | 7.0 High |
| In the Linux kernel, the following vulnerability has been resolved: gpiolib: fix race condition for gdev->srcu If two drivers were calling gpiochip_add_data_with_key(), one may be traversing the srcu-protected list in gpio_name_to_desc(), meanwhile other has just added its gdev in gpiodev_add_to_list_unlocked(). This creates a non-mutexed and non-protected timeframe, when one instance is dereferencing and using &gdev->srcu, before the other has initialized it, resulting in crash: [ 4.935481] Unable to handle kernel paging request at virtual address ffff800272bcc000 [ 4.943396] Mem abort info: [ 4.943400] ESR = 0x0000000096000005 [ 4.943403] EC = 0x25: DABT (current EL), IL = 32 bits [ 4.943407] SET = 0, FnV = 0 [ 4.943410] EA = 0, S1PTW = 0 [ 4.943413] FSC = 0x05: level 1 translation fault [ 4.943416] Data abort info: [ 4.943418] ISV = 0, ISS = 0x00000005, ISS2 = 0x00000000 [ 4.946220] CM = 0, WnR = 0, TnD = 0, TagAccess = 0 [ 4.955261] GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0 [ 4.955268] swapper pgtable: 4k pages, 48-bit VAs, pgdp=0000000038e6c000 [ 4.961449] [ffff800272bcc000] pgd=0000000000000000 [ 4.969203] , p4d=1000000039739003 [ 4.979730] , pud=0000000000000000 [ 4.980210] phandle (CPU): 0x0000005e, phandle (BE): 0x5e000000 for node "reset" [ 4.991736] Internal error: Oops: 0000000096000005 [#1] PREEMPT SMP ... [ 5.121359] pc : __srcu_read_lock+0x44/0x98 [ 5.131091] lr : gpio_name_to_desc+0x60/0x1a0 [ 5.153671] sp : ffff8000833bb430 [ 5.298440] [ 5.298443] Call trace: [ 5.298445] __srcu_read_lock+0x44/0x98 [ 5.309484] gpio_name_to_desc+0x60/0x1a0 [ 5.320692] gpiochip_add_data_with_key+0x488/0xf00 5.946419] ---[ end trace 0000000000000000 ]--- Move initialization code for gdev fields before it is added to gpio_devices, with adjacent initialization code. Adjust goto statements to reflect modified order of operations [Bartosz: fixed a build issue, removed stray newline] | ||||
| CVE-2026-23013 | 1 Linux | 1 Linux Kernel | 2026-01-26 | 7.0 High |
| In the Linux kernel, the following vulnerability has been resolved: net: octeon_ep_vf: fix free_irq dev_id mismatch in IRQ rollback octep_vf_request_irqs() requests MSI-X queue IRQs with dev_id set to ioq_vector. If request_irq() fails part-way, the rollback loop calls free_irq() with dev_id set to 'oct', which does not match the original dev_id and may leave the irqaction registered. This can keep IRQ handlers alive while ioq_vector is later freed during unwind/teardown, leading to a use-after-free or crash when an interrupt fires. Fix the error path to free IRQs with the same ioq_vector dev_id used during request_irq(). | ||||
| CVE-2026-23008 | 1 Linux | 1 Linux Kernel | 2026-01-26 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: drm/vmwgfx: Fix KMS with 3D on HW version 10 HW version 10 does not have GB Surfaces so there is no backing buffer for surface backed FBs. This would result in a nullptr dereference and crash the driver causing a black screen. | ||||
| CVE-2025-39945 | 1 Linux | 1 Linux Kernel | 2026-01-23 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: cnic: Fix use-after-free bugs in cnic_delete_task The original code uses cancel_delayed_work() in cnic_cm_stop_bnx2x_hw(), which does not guarantee that the delayed work item 'delete_task' has fully completed if it was already running. Additionally, the delayed work item is cyclic, the flush_workqueue() in cnic_cm_stop_bnx2x_hw() only blocks and waits for work items that were already queued to the workqueue prior to its invocation. Any work items submitted after flush_workqueue() is called are not included in the set of tasks that the flush operation awaits. This means that after the cyclic work items have finished executing, a delayed work item may still exist in the workqueue. This leads to use-after-free scenarios where the cnic_dev is deallocated by cnic_free_dev(), while delete_task remains active and attempt to dereference cnic_dev in cnic_delete_task(). A typical race condition is illustrated below: CPU 0 (cleanup) | CPU 1 (delayed work callback) cnic_netdev_event() | cnic_stop_hw() | cnic_delete_task() cnic_cm_stop_bnx2x_hw() | ... cancel_delayed_work() | /* the queue_delayed_work() flush_workqueue() | executes after flush_workqueue()*/ | queue_delayed_work() cnic_free_dev(dev)//free | cnic_delete_task() //new instance | dev = cp->dev; //use Replace cancel_delayed_work() with cancel_delayed_work_sync() to ensure that the cyclic delayed work item is properly canceled and that any ongoing execution of the work item completes before the cnic_dev is deallocated. Furthermore, since cancel_delayed_work_sync() uses __flush_work(work, true) to synchronously wait for any currently executing instance of the work item to finish, the flush_workqueue() becomes redundant and should be removed. This bug was identified through static analysis. To reproduce the issue and validate the fix, I simulated the cnic PCI device in QEMU and introduced intentional delays — such as inserting calls to ssleep() within the cnic_delete_task() function — to increase the likelihood of triggering the bug. | ||||